PROJECT 14 / SUPPORTS & JOINTS
These examples calculate forces from selected drawing outlines. Supports and extra loads are assumed so the options can be compared.
Support positions, load cases, fixings and joint details were not supplied. The following examples are created for comparison; they do not establish that any completed job or proposed installation is safe.
How to read these forces → · Drawing gaps for this project →
Each outline has its own drawing. Open a component to see its forces, assumed supports and worked calculations.
Small rectangular kitchen islandisland · view calculation →
Rectangular lower-section vanityvanity · view calculation →
Upper cooker-side counter leftcounter · view calculation →
Surround left upright stripwall trim · view calculation →
Surround left lower panelwall panel · view calculation →
Three shelf/panel rectanglesshelf · view calculation →Results are per physical piece; quantities are shown separately. Alternative drawing sheets are not added together. Horizontal surface examples add an illustrative 500 N point load to stone self-weight; trim strips and vertical panels use self-weight only.
| Component / source | Thickness basis | Scenario mass / gravity | Support demand | Strength check |
|---|---|---|---|---|
| Small rectangular kitchen islandproject-14a.jpg · qty 1; results per piece | 30 mmdrawing reading | 61.4 kg602.1 N self-weight | R₁ 551.1 N R₂ 551.1 N | UnverifiedDemand only; resistance not established |
| Rectangular lower-section vanityproject-14a.jpg · qty 1; results per piece | 30 mmdrawing reading | 47.5 kg466.4 N self-weight | R₁ 483.2 N R₂ 483.2 N | UnverifiedDemand only; resistance not established |
| Upper-left green-stone vanityproject-14a.jpg · qty 1; results per piece | 20 mmdrawing reading | 30.3 kg297.1 N self-weight | R₁ 398.5 N R₂ 398.5 N | UnverifiedDemand only; resistance not established |
| Upper cooker-side counter leftproject-14b.jpg · qty 1; results per piece | 30 mmdrawing reading | 72.9 kg714.9 N self-weight | R₁ 607.4 N R₂ 607.4 N | UnverifiedDemand only; resistance not established |
| Upper cooker-side counter rightproject-14b.jpg · qty 1; results per piece | 30 mmdrawing reading | 72.9 kg714.9 N self-weight | R₁ 607.4 N R₂ 607.4 N | UnverifiedDemand only; resistance not established |
| Upper long counterproject-14b.jpg · qty 1; results per piece | 30 mmdrawing reading | 112.8 kg1,106.5 N self-weight | R₁ 803.2 N R₂ 803.2 N | UnverifiedDemand only; resistance not established |
| Small upper-floor vanityproject-14b.jpg · qty 1; results per piece | 20 mmdrawing reading | 21.4 kg210.2 N self-weight | R₁ 355.1 N R₂ 355.1 N | UnverifiedDemand only; resistance not established |
| Surround left upright stripproject-14b.jpg · qty 1; results per piece | 20 mmdrawing reading | 15.4 kg151.5 N self-weight | Ledger 151.5 N Restraint couple 23.6 N | UnverifiedDemand only; resistance not established |
| Surround right upright stripproject-14b.jpg · qty 1; results per piece | 20 mmdrawing reading | 15.0 kg147.6 N self-weight | Ledger 147.6 N Restraint couple 23.5 N | UnverifiedDemand only; resistance not established |
| Surround left lower panelproject-14b.jpg · qty 1; results per piece | 20 mmdrawing reading | 34.3 kg336.3 N self-weight | Ledger 336.3 N Restraint couple 33.6 N | UnverifiedDemand only; resistance not established |
| Surround central lower panelproject-14b.jpg · qty 1; results per piece | 20 mmdrawing reading | 79.3 kg777.7 N self-weight | Ledger 777.7 N Restraint couple 77.8 N | UnverifiedDemand only; resistance not established |
| Surround right lower panelproject-14b.jpg · qty 1; results per piece | 20 mmdrawing reading | 34.1 kg334.5 N self-weight | Ledger 334.5 N Restraint couple 33.5 N | UnverifiedDemand only; resistance not established |
| Three shelf/panel rectanglesproject-14b.jpg · qty 3; results per piece | 20 mmdrawing reading | 32.5 kg319.0 N self-weight | R₁ 409.5 N R₂ 409.5 N | UnverifiedDemand only; resistance not established |
| Hood surround front panelproject-14b.jpg · qty 1; results per piece | 20 mmdrawing reading | 69.9 kg685.7 N self-weight | Ledger 685.7 N Restraint couple 68.6 N | UnverifiedDemand only; resistance not established |
| Hood surround side panelsproject-14b.jpg · qty 2; results per piece | 20 mmdrawing reading | 26.6 kg260.7 N self-weight | Ledger 260.7 N Restraint couple 26.1 N | UnverifiedDemand only; resistance not established |
Gross dimensions remain unverified drawing readings. Assumed 20 mm thicknesses and proxy densities are identified in every worked record. These scenario inputs do not replace the fixed measurement tables.
Gross area 0.8525 m²; thickness 30 mm (drawing reading); density 2,400 kg/m³ (Estimate · historical TCE family range). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 0.8525 × 0.030 × 2,400 = 61.38 kg
W = m × 9.81 = 602.11 NAssumed end support lines: x = 0 and L = 1.1049 m
Gross-outline centre of mass x̄ = 0.5524 m
Illustrative additional point load P = 500 N at x = L/2
R₂ = (W × x̄ + P × L/2) ÷ L = 551.05 N
R₁ = W + P − R₂ = 551.05 N
Check: R₁ + R₂ = W + P = 1,102.11 N500 N, where included, is an example load (about a 51 kg mass equivalent), not a prescribed residential design load. Trim-strip examples use self-weight only. The end-line model is a statics exercise: it does not permit this stone to span the full length. Actual rails, cutouts and supports can create a different load distribution.
If the right edge is a supported butt seam, this piece contributes 551.1 N to its support in the assumed load case. Add the adjoining piece’s edge reaction and applicable loads before selecting that support. No actual seam position or adjoining load is confirmed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 0.6603 m²; thickness 30 mm (drawing reading); density 2,400 kg/m³ (Estimate · historical TCE family range). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 0.6603 × 0.030 × 2,400 = 47.54 kg
W = m × 9.81 = 466.40 NAssumed end support lines: x = 0 and L = 1.1684 m
Gross-outline centre of mass x̄ = 0.5842 m
Illustrative additional point load P = 500 N at x = L/2
R₂ = (W × x̄ + P × L/2) ÷ L = 483.20 N
R₁ = W + P − R₂ = 483.20 N
Check: R₁ + R₂ = W + P = 966.40 N500 N, where included, is an example load (about a 51 kg mass equivalent), not a prescribed residential design load. Trim-strip examples use self-weight only. The end-line model is a statics exercise: it does not permit this stone to span the full length. Actual rails, cutouts and supports can create a different load distribution.
If the right edge is a supported butt seam, this piece contributes 483.2 N to its support in the assumed load case. Add the adjoining piece’s edge reaction and applicable loads before selecting that support. No actual seam position or adjoining load is confirmed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 0.5610 m²; thickness 20 mm (drawing reading); density 2,699 kg/m³ (Estimate · generic marble proxy). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 0.5610 × 0.020 × 2,699 = 30.28 kg
W = m × 9.81 = 297.07 NAssumed end support lines: x = 0 and L = 1.0096 m
Gross-outline centre of mass x̄ = 0.5048 m
Illustrative additional point load P = 500 N at x = L/2
R₂ = (W × x̄ + P × L/2) ÷ L = 398.53 N
R₁ = W + P − R₂ = 398.53 N
Check: R₁ + R₂ = W + P = 797.07 N500 N, where included, is an example load (about a 51 kg mass equivalent), not a prescribed residential design load. Trim-strip examples use self-weight only. The end-line model is a statics exercise: it does not permit this stone to span the full length. Actual rails, cutouts and supports can create a different load distribution.
If the right edge is a supported butt seam, this piece contributes 398.5 N to its support in the assumed load case. Add the adjoining piece’s edge reaction and applicable loads before selecting that support. No actual seam position or adjoining load is confirmed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 1.0121 m²; thickness 30 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 1.0121 × 0.030 × 2,400 = 72.87 kg
W = m × 9.81 = 714.86 NAssumed end support lines: x = 0 and L = 1.5938 m
Gross-outline centre of mass x̄ = 0.7969 m
Illustrative additional point load P = 500 N at x = L/2
R₂ = (W × x̄ + P × L/2) ÷ L = 607.43 N
R₁ = W + P − R₂ = 607.43 N
Check: R₁ + R₂ = W + P = 1,214.86 N500 N, where included, is an example load (about a 51 kg mass equivalent), not a prescribed residential design load. Trim-strip examples use self-weight only. The end-line model is a statics exercise: it does not permit this stone to span the full length. Actual rails, cutouts and supports can create a different load distribution.
If the right edge is a supported butt seam, this piece contributes 607.4 N to its support in the assumed load case. Add the adjoining piece’s edge reaction and applicable loads before selecting that support. No actual seam position or adjoining load is confirmed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 1.0121 m²; thickness 30 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 1.0121 × 0.030 × 2,400 = 72.87 kg
W = m × 9.81 = 714.86 NAssumed end support lines: x = 0 and L = 1.5938 m
Gross-outline centre of mass x̄ = 0.7969 m
Illustrative additional point load P = 500 N at x = L/2
R₂ = (W × x̄ + P × L/2) ÷ L = 607.43 N
R₁ = W + P − R₂ = 607.43 N
Check: R₁ + R₂ = W + P = 1,214.86 N500 N, where included, is an example load (about a 51 kg mass equivalent), not a prescribed residential design load. Trim-strip examples use self-weight only. The end-line model is a statics exercise: it does not permit this stone to span the full length. Actual rails, cutouts and supports can create a different load distribution.
If the right edge is a supported butt seam, this piece contributes 607.4 N to its support in the assumed load case. Add the adjoining piece’s edge reaction and applicable loads before selecting that support. No actual seam position or adjoining load is confirmed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 1.5665 m²; thickness 30 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 1.5665 × 0.030 × 2,400 = 112.79 kg
W = m × 9.81 = 1,106.47 NAssumed end support lines: x = 0 and L = 2.4670 m
Gross-outline centre of mass x̄ = 1.2335 m
Illustrative additional point load P = 500 N at x = L/2
R₂ = (W × x̄ + P × L/2) ÷ L = 803.24 N
R₁ = W + P − R₂ = 803.24 N
Check: R₁ + R₂ = W + P = 1,606.47 N500 N, where included, is an example load (about a 51 kg mass equivalent), not a prescribed residential design load. Trim-strip examples use self-weight only. The end-line model is a statics exercise: it does not permit this stone to span the full length. Actual rails, cutouts and supports can create a different load distribution.
If the right edge is a supported butt seam, this piece contributes 803.2 N to its support in the assumed load case. Add the adjoining piece’s edge reaction and applicable loads before selecting that support. No actual seam position or adjoining load is confirmed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 0.4463 m²; thickness 20 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 0.4463 × 0.020 × 2,400 = 21.42 kg
W = m × 9.81 = 210.16 NAssumed end support lines: x = 0 and L = 0.8033 m
Gross-outline centre of mass x̄ = 0.4016 m
Illustrative additional point load P = 500 N at x = L/2
R₂ = (W × x̄ + P × L/2) ÷ L = 355.08 N
R₁ = W + P − R₂ = 355.08 N
Check: R₁ + R₂ = W + P = 710.16 N500 N, where included, is an example load (about a 51 kg mass equivalent), not a prescribed residential design load. Trim-strip examples use self-weight only. The end-line model is a statics exercise: it does not permit this stone to span the full length. Actual rails, cutouts and supports can create a different load distribution.
If the right edge is a supported butt seam, this piece contributes 355.1 N to its support in the assumed load case. Add the adjoining piece’s edge reaction and applicable loads before selecting that support. No actual seam position or adjoining load is confirmed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 0.3217 m²; thickness 20 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 0.3217 × 0.020 × 2,400 = 15.44 kg
W = m × 9.81 = 151.50 NLower bearing demand R = W = 151.5 N
Assumed offset e = 0.030 m; restraint separation h = 0.1924 m
M = W × e = 4.54 N·m
T = M ÷ h = 23.62 NThe assumed separation is the smaller of 300 mm and 60% of the panel’s short outside dimension. This keeps the example couple within its outline; it does not establish anchor placement or edge clearances. The forces form an idealized upper-restraint/lower-bearing couple for one panel. They are not individual anchor capacities. Anchor prying, shared load, substrate strength and lateral/seismic loads are unassigned.
The bottom joint or ledger must transfer at least the 151.5 N modeled gravity demand from this panel, plus other applicable design actions. Adhesive-only suspension is not assumed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 0.3134 m²; thickness 20 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 0.3134 × 0.020 × 2,400 = 15.04 kg
W = m × 9.81 = 147.56 NLower bearing demand R = W = 147.6 N
Assumed offset e = 0.030 m; restraint separation h = 0.1886 m
M = W × e = 4.43 N·m
T = M ÷ h = 23.47 NThe assumed separation is the smaller of 300 mm and 60% of the panel’s short outside dimension. This keeps the example couple within its outline; it does not establish anchor placement or edge clearances. The forces form an idealized upper-restraint/lower-bearing couple for one panel. They are not individual anchor capacities. Anchor prying, shared load, substrate strength and lateral/seismic loads are unassigned.
The bottom joint or ledger must transfer at least the 147.6 N modeled gravity demand from this panel, plus other applicable design actions. Adhesive-only suspension is not assumed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 0.7142 m²; thickness 20 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 0.7142 × 0.020 × 2,400 = 34.28 kg
W = m × 9.81 = 336.30 NLower bearing demand R = W = 336.3 N
Assumed offset e = 0.030 m; restraint separation h = 0.3000 m
M = W × e = 10.09 N·m
T = M ÷ h = 33.63 NThe assumed separation is the smaller of 300 mm and 60% of the panel’s short outside dimension. This keeps the example couple within its outline; it does not establish anchor placement or edge clearances. The forces form an idealized upper-restraint/lower-bearing couple for one panel. They are not individual anchor capacities. Anchor prying, shared load, substrate strength and lateral/seismic loads are unassigned.
The bottom joint or ledger must transfer at least the 336.3 N modeled gravity demand from this panel, plus other applicable design actions. Adhesive-only suspension is not assumed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 1.6516 m²; thickness 20 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 1.6516 × 0.020 × 2,400 = 79.28 kg
W = m × 9.81 = 777.72 NLower bearing demand R = W = 777.7 N
Assumed offset e = 0.030 m; restraint separation h = 0.3000 m
M = W × e = 23.33 N·m
T = M ÷ h = 77.77 NThe assumed separation is the smaller of 300 mm and 60% of the panel’s short outside dimension. This keeps the example couple within its outline; it does not establish anchor placement or edge clearances. The forces form an idealized upper-restraint/lower-bearing couple for one panel. They are not individual anchor capacities. Anchor prying, shared load, substrate strength and lateral/seismic loads are unassigned.
The bottom joint or ledger must transfer at least the 777.7 N modeled gravity demand from this panel, plus other applicable design actions. Adhesive-only suspension is not assumed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 0.7105 m²; thickness 20 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 0.7105 × 0.020 × 2,400 = 34.10 kg
W = m × 9.81 = 334.55 NLower bearing demand R = W = 334.5 N
Assumed offset e = 0.030 m; restraint separation h = 0.3000 m
M = W × e = 10.04 N·m
T = M ÷ h = 33.45 NThe assumed separation is the smaller of 300 mm and 60% of the panel’s short outside dimension. This keeps the example couple within its outline; it does not establish anchor placement or edge clearances. The forces form an idealized upper-restraint/lower-bearing couple for one panel. They are not individual anchor capacities. Anchor prying, shared load, substrate strength and lateral/seismic loads are unassigned.
The bottom joint or ledger must transfer at least the 334.5 N modeled gravity demand from this panel, plus other applicable design actions. Adhesive-only suspension is not assumed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 0.6774 m²; thickness 20 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 0.6774 × 0.020 × 2,400 = 32.52 kg
W = m × 9.81 = 318.98 NAssumed end support lines: x = 0 and L = 1.2700 m
Gross-outline centre of mass x̄ = 0.6350 m
Illustrative additional point load P = 500 N at x = L/2
R₂ = (W × x̄ + P × L/2) ÷ L = 409.49 N
R₁ = W + P − R₂ = 409.49 N
Check: R₁ + R₂ = W + P = 818.98 N500 N, where included, is an example load (about a 51 kg mass equivalent), not a prescribed residential design load. Trim-strip examples use self-weight only. The end-line model is a statics exercise: it does not permit this stone to span the full length. Actual rails, cutouts and supports can create a different load distribution.
If the right edge is a supported butt seam, this piece contributes 409.5 N to its support in the assumed load case. Add the adjoining piece’s edge reaction and applicable loads before selecting that support. No actual seam position or adjoining load is confirmed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 1.4562 m²; thickness 20 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 1.4562 × 0.020 × 2,400 = 69.90 kg
W = m × 9.81 = 685.70 NLower bearing demand R = W = 685.7 N
Assumed offset e = 0.030 m; restraint separation h = 0.3000 m
M = W × e = 20.57 N·m
T = M ÷ h = 68.57 NThe assumed separation is the smaller of 300 mm and 60% of the panel’s short outside dimension. This keeps the example couple within its outline; it does not establish anchor placement or edge clearances. The forces form an idealized upper-restraint/lower-bearing couple for one panel. They are not individual anchor capacities. Anchor prying, shared load, substrate strength and lateral/seismic loads are unassigned.
The bottom joint or ledger must transfer at least the 685.7 N modeled gravity demand from this panel, plus other applicable design actions. Adhesive-only suspension is not assumed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
Gross area 0.5535 m²; thickness 20 mm (drawing reading); density 2,400 kg/m³ (Estimate · comparable quartz). Openings are not deducted; cutout stress concentrations and remaining stone strips need a separate check.
m = A × t × ρ = 0.5535 × 0.020 × 2,400 = 26.57 kg
W = m × 9.81 = 260.65 NLower bearing demand R = W = 260.7 N
Assumed offset e = 0.030 m; restraint separation h = 0.3000 m
M = W × e = 7.82 N·m
T = M ÷ h = 26.07 NThe assumed separation is the smaller of 300 mm and 60% of the panel’s short outside dimension. This keeps the example couple within its outline; it does not establish anchor placement or edge clearances. The forces form an idealized upper-restraint/lower-bearing couple for one panel. They are not individual anchor capacities. Anchor prying, shared load, substrate strength and lateral/seismic loads are unassigned.
The bottom joint or ledger must transfer at least the 260.7 N modeled gravity demand from this panel, plus other applicable design actions. Adhesive-only suspension is not assumed.
Capacity pending: stone bending and deflection, local bearing, support stiffness, joint shear/peel, connection capacity, load factors and the final design load combinations are not established. A bond area or an adhesive coupon strength alone cannot establish the installed joint’s capacity.
This example uses TCE1220 at 30 mm and 2,400 kg/m³. It does not claim this overhang exists in Project 14. A 350 mm overhang, 400 mm tributary width and 500 N tip load are deliberately assumed.
W_bay = ρ × t × 0.400 × 0.350 × 9.81 = 98.88 N
V = W_bay + 500 = 598.88 N
M_root = W_bay × 0.350/2 + 500 × 0.350
= 192.30 N·m
For a separate ideal connection with h = 0.150 m:
T_couple = M_root ÷ h = 1,282.03 NThe 150 mm force-couple lever arm is an algebra example for a vertically separated connection. It is not the Liberty’s flush-mounted lag-screw geometry or an anchor specification.
Published carry reference: 375 lbf per bracket ≈ 1,668 N. The bracket has a 12 in support projection plus 4⅛ in mounting length, with a 3 in width and ¼ in steel thickness.
Its guide calls for double 2×4 knee-wall blocking tied into the floor, flush/level mounting and spacing no greater than 18 in (457 mm). The 400 mm example bay is within that spacing figure. The assumed 350 mm overhang extends about 45 mm beyond the 305 mm arm; permissible stone extension still needs confirmation.
Comparison, not approval: the calculated 599 N shear is 35.9% of the catalog force reference. The guide does not establish the actual anchor-group moment resistance, stone capacity, test load position or an applicable design safety factor. Those checks remain open.
Required resistance must cover the governing design demand on a consistent load/resistance basis. These pages calculate selected service-load demands; they do not supply tested allowable capacities or a code-compliant design factor. Stone cracking, deflection and joint failure therefore remain unresolved.
Force balance and moments use algebra: ΣF = 0 and ΣM = 0. No calculus is required for these demand examples.
TCE Stone Quartz products in Canada; no thickness-specific support schedule. No verified TCE numeric overhang, bracket-spacing or wall-anchor guidance was found in public resources. Request current regional installation instructions; do not transplant another brand table.
Manufacturer tables apply only within their stated products, thicknesses, regions and installation conditions. They are not copied into a universal allowable-span rule. Research checked 24 October 2026.
Download assumptions and calculation record ↓